top of page

FISHEYE SUPPORT

Find installation guidance, product manuals, troubleshooting help, and compatibility information.

Open book for FishEye self-help resources

SELF HELP

Find installation, operation, troubleshooting, and compatibility guidance

FishEye manuals and downloads

MANUALS & DOWNLOADS

View FishEye product manuals, installation guides, and downloadable documents.

SELF-HELP TOPICS

Browse helpful articles and guides to get the most out of your FishEye.

FishEye installation and setup help

INSTALLATION & SETUP

Mounting options, power connection and setup instructions.

FishEye operation and control guidance

OPERATION & CONTROLS

Learn how to use your remote, aim your sonar and operate your FishEye.

FishEye troubleshooting help

TROUBLESHOOTING

Diagnose and solve

common issues and get back up and running.

FishEye parts and compatibility information

PARTS & COMPATIBILITY

Find compatible parts, accessories and answers about your system.

TROUBLESHOOTING

Find the cause of common FishEye problems and follow safe checks before contacting support.

Troubleshoot a FishEye with no power

NO POWER

Check power and connections.

Troubleshoot FishEye raising and lowering

RAISE & LOWER

Fix lift movement problems.

Troubleshoot FishEye aiming and controls

AIMING & CONTROLS

Fix control or rotation issues.

Troubleshoot FishEye sonar image problems

SONAR IMAGE

Fix direction or image issues.

INSTALLATION & SETUP

Choose your installation type to view the correct setup guidance.

FishEye permanent transom installation

PERMANENT TRANSOM

Mounted directly to the boat.

FishEye removable clamp installation

REMOVABLE CLAMP

Portable clamp-on installation.

FishEye kayak installation

KAYAK

Compact setup for small watercraft.

PARTS & COMPATIBILITY

Find compatible parts for your FishEye setup.

Check FishEye boat compatibility

BOAT

Works with your boat.

Check FishEye sonar compatibility

SONAR

Works with your sonar.

Check FishEye power compatibility

POWER

Works with your power source.

OPERATION & CONTROLS

Learn how to lower, aim, operate and store your FishEye system safely.

Getting started with FishEye

GETTING STARTED

Power on the FishEye and prepare it for use.

Lowering and raising the FishEye

LOWERING & RAISING

Deploy the sonar into the water and return it to the stored position.

Aiming and controlling FishEye sonar

AIMING & SONAR CONTROL

Aim the transducer independently and understand its direction.

FishEye remote control functions

CONTROL FUNCTIONS

Learn the FishEye controls, indicators and normal operating responses.

PERMANENT TRANSOM INSTALLATION

For FishEye systems mounted directly to the boat's transom.

CHOOSE THE MOUNTING LOCATION

Dry-fit the FishEye before drilling or tightening anything.

Choose a location where the system can move through its full raised, lowered and aiming positions without contacting.​​

  • The outboard motor

  • The propeller

  • Steering components

  • Trim tabs or ladders

  • The hull

  • Other transducers or accessories

Look behind the transom before drilling to confirm that wiring, fuel lines, tanks, or structural components are not in the way.

Do not continue if the FishEye cannot move freely in every operating position.

Position the Mount

Hold the mount against the selected location and confirm that it is straight, stable and supported by a solid part of the transom

With the FishEye temporarily positioned:

  • Check the raised storage position.

  • Check the fully lowered operating position.

  • Confirm the transducer can sit in the required position below the hull.

  • Turn and trim the motor through its normal range.

  • Verify that the FishEye and its cables remain clear.

Mark the mounting location only after completing these clearance checks.

Secure the Mounting Hardware

Install the permanent mount using the supplied hardware and the FishEye mounting diagram.

Before fastening:

  • Confirm the mount is level and correctly oriented.

  • Check both sides of the transom for obstructions.

  • Use an appropriate marine sealant around any drilled mounting holes.

  • Use backing hardware when specified in the FishEye instructions.

  • Tighten the fasteners evenly so the mount sits flat against the transom.

Do not use unapproved hardware or drill into the boat until the mounting location has been confirmed.

Install the FishEye Assembly

Attach the FishEye shaft and operating assembly to the secured mount using the supplied fasteners.

After assembly:

  • Confirm the shaft is properly seated.

  • Verify that retaining pins, bolts or locking hardware are fully engaged.

  • Check that the assembly cannot slide or rotate unexpectedly.

  • Move the FishEye through its complete operating range by hand, if permitted.

  • Confirm that no component binds or contacts the boat.

Stop and recheck the assembly if movement feels restricted, uneven or unstable.

Route Power and Transducer Cables

Route the cables only after confirming the system's complete range of movement.

The cables should:​

  • Stay clear of the propeller and motor.

  • Avoid sharp edges and hot surfaces.

  • Have enough slack for normal FishEye movement.

  • Not hang loosely where they can snag.

  • Be supported with marine-grade cable ties or clamps.

  • Avoid tight bends, pinch points and excessive tension.

Leave the power disconnected while routing or adjusting wiring. Connect power only according to the FishEye power instructions.

Test Before Use

Test the complete installation before launching the boat.

With the boat safely parked or secured:

  • Recheck every mounting fastener.

  • Confirm the FishEye assembly is locked into position.

  • Connect the approved power source.

  • Test raising and lowering.

  • Test the full aiming or rotation range.

  • Watch the cables during the movement.

  • Confirm the controls respond in the correct direction.

  • Stop immediately if anything binds, pulls, vibrates or contacts the boat.

After the first use, inspect the mount, hardware and cables again for movement or loosening.

FREQUENTLY ASKED QUESTIONS

Quick answers about choosing, installing and using your FishEye.

Which FishEye setup is right for me?

Choose your configuration according to where the system will be installed.

  • Permanent transom

  • Removable transom clamp

  • Kayak or small watercraft

Use Choose Your FishEye for a guided recommendation based on your mounting location and preferred power source.

Will FishEye work with my sonar?

Compatibility depends on your exact transducer model, mounting requirements, and FishEye configuration.

  • Permanent transom

  • Removable transom clamp

  • Kayak or small watercraft

Use Choose Your FishEye for a guided recommendation based on your mounting location and preferred power source.

What power source does FishEye require?

Depending on the configuration, FishEye uses either:

  • Approved 12-volt boat power connection

  • A compatible tool-battery adapter and battery. Compatible with:

    • DeWalt​

    • Makita

    • Milwaukee

Check Parts & Compatibility Power for the required voltage, connection and recommended battery capacity. Do not connect an unapproved power source.

Can I install FishEye myself?

Many FishEye installations can be completed with common tools and the correct installation guide. Difficulty depends on the mounting configuration, boat and available mounting surface.

Before drilling or permanently attaching anything:

  • Dry-fit the complete system

  • Check the full raising, lowering and aiming range

  • Confirm clearance from the motor, propeller and steering components

  • Plan a safe path for the power and transducer cables

Select your configuration under Installation & Setup for complete instructions.

How does FishEye aim the sonar?

FishEye allows the sonar transducer to be aimed by remote independently from the direction the boat is facing.

The directional arrow on top of the FishEye indicates where the sonar is pointing. Before launching, confirm that the arrow and sonar image respond in the expected direction.

What should I check if my FishEye is not working?

Start with these basic checks:

  1. Verify the power switch is in the on position. Power is on if switch is illuminated.

  2. Confirm the approved power source is connected and charged

  3. Inspect the fuse, wiring and connectors

  4. Check for cable tension, obstructions or binding

  5. Confirm the transducer and mounting hardware are secure

  6. Make sure the system can raise, lower and aim freely

Stop using the system if it moves unexpectedly, contacts another component or places tension on a cable. Select the appropriate Troubleshooting guide for additional steps.

GETTING STARTED

Use this startup process before operating the FishEye or lowering the sonar into the water.

Inspect the FishEye System

Inspect the complete FishEye installation before connecting power or deploying the sonar.

Confirm that:

  • The FishEye mount is securely attached

  • All visible mounting hardware is tight

  • The shaft and moving components are undamaged

  • The transducer is firmly attached

  • Power and transducer cables are connected securely

  • No cable is out, pinched, stretched or wrapped around the assembly

  • The FishEye has a clear path through its complete movement range

Do not operate the FishEye if any component is loose, damaged or incorrectly positioned.

Check the Operating Area

Make sure the FishEye can be operated without contacting the boat, kayak, dock, or surrounding objects.

Before lowering the system:

  • Confirm there is sufficient water depth

  • Keep the FishEye clear of the dock and trailer

  • Check for weeds, fishing line and underwater obstructions

  • Keep people, equipment and loose cables away from moving components

  • Confirm the transducer will remain clear of the propeller

  • Verify that the boat or kayak is safely secured and under control

Do not lower the FishEye while the boat is on its trailer or positioned over an obstruction.

Connect the Approved Power Source

Connect the FishEye only to the approved power source for the installed configuration.

Before connecting power:

  • Confirm that the power source matches FishEye requirements

  • Inspect the connector and wiring for damage

  • Verify that the connection is clean and dry

  • Confirm correct polarity when using a wired 12V connection

  • Secure the battery or tool-battery adapter

  • Keep the power cable clear of moving parts

Disconnect power immediately if the connector becomes hot, damaged or wet where it should remain dry.

Power On the FishEye and Sonar

Power on the FishEye and sonar equipment according to their supplied operating instructions.

After power is connected:

  • Confirm that the FishEye indicates it is receiving power

  • Verify that the sonar display starts normally

  • Check that the FishEye controls are connected or responding

  • Watch for unexpected movement when the system starts

  • Confirm that no cable pulls or twists

  • Stop if the system produces unusual noise or movement

Do not force the FishEye by hand while powered unless the supplied instructions specifically allow it.

Confirm the Control Direction

Test the controls briefly before relying on the FishEye to aim the sonar.

Verify that:

  • The control responds when activated

  • The FishEye moves in the expected direction

  • The transducer direction matches the sonar image

  • Movement is smooth and unobstructed

  • The system stops responding when the control is released

  • The cables remain free throughout the movement

If the sonar image appears reversed or the controls aim opposite the expected direction, stop and check the transducer orientation and control configuration.

Perform a Complete Function Check

Test the FishEye through its normal operating range before beginning to fish.

  1. Lower the FishEye into its operating position

  2. Confirm that the transducer is below the waterline

  3. Test the complete aiming range

  4. Watch the cables during movement

  5. Confirm the sonar display is receiving a usable image

  6. Raise the FishEye into its stored position

  7. Verify that the system stops and stores correctly

  8. Recheck the mount and hardware for movement

Stop immediately if the FishEye binds, contacts another component, pulls a cable or fails to respond normally.

Before You Fish

  • Lower the FishEye into its operating position

  • Confirm that the transducer is below the waterline

  • Test the complete aiming range

  • Watch the cables during movement

  • Confirm the sonar display is receiving a usable image

  • Raise the FishEye into its stored position

  • Verify that the system stops and stores correctly

  • Recheck the mount and hardware for movement

Safety Notice

Keep hands, clothing, fishing line and loose equipment away from moving FishEye components. Disconnect power before inspecting, adjusting or clearing an obstruction. Never operate the system where it could contact a person, propeller, dock, trailer or underwater object.

REMOVABLE CLAMP-ON INSTALLATION

For portable FishEye systems secured to the boat with a removable transom clamp.

Inspect the Clamp and Transom

Before installing, inspect the clamp, adjustment hardware and mounting surface.

Confirm that:

  • The clamp is complete and undamaged.

  • Adjustment screws turn smoothly.

  • Contact pads are secure.

  • The transom surface is solid, clean and reasonably flat.

  • Trim, molding or hardware will not prevent full contact.

Do not install the clamp over a loose, damaged or uneven surface.

Choose the Mounting location

Choose a transom location where the FishEye can raise, lower and aim without contacting the boat or motor.

Before tightening the clamp:

  • Turn and trim the motor through its normal range.

  • Check clearance from the propeller.

  • Check clearance from ladders, trim tabs and other transducers.

  • Confirm the shaft can move freely.

  • Make sure the clamp can sit completely against the transom.

Reposition the clamp if any component could interfere with normal operation.

Attach and Tighten the Clamp

Open the clamp far enough to fit over the transom without forcing it into place.

Then:

  • Seat the clamp fully against the transom.

  • Confirm both contact surfaces sit flat.

  • Keep the mounting assembly upright.

  • Tighten the adjustment hardware evenly.

  • Check that the clamp cannot slide, rock or twist.

The clamp should be secure without damaging or crushing the transom surface. Do not use tools for extra leverage unless the FishEye instructions specifically require them.

Install the FishEye Assembly

Attach the FishEye shaft and operating assembly to the secured mount using the supplied hardware.

After installation:

  • Confirm the shaft is properly seated.

  • Engage all retaining pins, locks or fasteners.

  • Verify that the assembly cannot lift out unexpectedly.

  • Check that the shaft remains upright.

  • Move the system through its available range by hand, if permitted.

Stop and recheck the assembly if movement feels restricted, uneven or unstable.

Route Power and Transducer Cables

Route the cables only after confirming the system's complete range of movement.

The cables should:​

  • Stay clear of the propeller and motor.

  • Avoid sharp edges and hot surfaces.

  • Have enough slack for normal FishEye movement.

  • Not hang loosely where they can snag.

  • Be supported with marine-grade cable ties or clamps.

  • Avoid tight bends, pinch points and excessive tension.

Leave the power disconnected while routing or adjusting wiring. Connect power only according to the FishEye power instructions.

Test Before Use

Test the complete installation before launching the boat.

With the boat safely parked or secured:

  • Recheck every mounting fastener.

  • Confirm the FishEye assembly is locked into position.

  • Connect the approved power source.

  • Test raising and lowering.

  • Test the full aiming or rotation range.

  • Watch the cables during the movement.

  • Confirm the controls respond in the correct direction.

  • Stop immediately if anything binds, pulls, vibrates or contacts the boat.

After the first use, inspect the mount, hardware and cables again for movement or loosening.

LOWERING & RAISING

Use these steps to move the FishEye safely between its stored and operating positions.

Check the Area Before Moving the FishEye

Inspect the area around and below the FishEye before using the lowering or raising control.

Confirm that:

  • The boat or kayak is safely secured or under control

  • There is enough water depth for the FishEye

  • The assembly is clear of the dock, trailer and shoreline

  • No fishing line, weeds or debris are wrapped around the system

  • People and loose equipment are away from moving components

  • The transducer will remain clear of the propeller

  • The power and transducer cable can move freely

Do not lower the FishEye while the boat is on its trailer or positioned over an obstruction.

Prepare the System for Lowering

Confirm that the FishEye is ready to move from its stored position.

Before activating the control:

  1. Connect the approved power source

  2. Confirm that the mount and hardware are secure

  3. Release any storage strap, lock or transportation restraint

  4. Check that the shaft is not caught on a cable or other equipment

  5. Verify that the transducer is securely attached

  6. Keep hands and equipment away from the movement path

Lower the FishEye into the Water

Use the designated FishEye control to lower the assembly gradually into its operating position.

While lowering:

  • Watch the complete assembly

  • Keep the shaft clear of the boat or kayak

  • Monitor the cables for pulling or pinching

  • Listen for unusual grinding, clicking or straining

  • Release the controls if the FishEye meets resistance

  • Confirm that the transducer enters the water without striking the hull

Do not continue activating the control if the FishEye stops moving or contacts an obstruction.

Confirm the Operating Position

After lowering, verify that the FishEye is positioned correctly before aiming the sonar.

Confirm that:

  • The transducer is below the waterline

  • The sonar has a clear view beneath or ahead of the boat

  • The assembly remains clear of the hull or propeller

  • The shaft is stable and correctly aimed

  • The cables retain enough slack for aiming

  • The sonar display is receiving a usable image

  • The FishEye can rotate or aim without obstruction

Lower the system only to the approved operating depth. Excessive depth may increase the risk of striking underwater objects.

Raise the FishEye Before Hazards

Raise the FishEye before approaching conditions that could damage the system.

Raise it before:

  • Entering shallow water

  • Beaching or loading a kayak

  • Approaching a dock or trailer

  • Moving through heavy weeds or debris

  • Operating at higher travel speeds

  • Stowing the trolling motor, when applicable

  • Loading or transporting the boat

  • Removing the boat from the water

Watch the assembly and cables throughout the complete raising movement.

Confirm the Stored Position

Continue raising the FishEye until it reaches its designated stored position.

  1. Confirm that the transducer is completely clear of the water

  2. Verify that the system has stopped moving

  3. Check that no cable is pinched or under tension

  4. Confirm the FishEye will not contact the dock, trailer or other equipment

  5. Engage the storage lock, strap or transportation restraint when required

  6. Disconnect power before adjustment, removal or transportation

  7. Inspect the mount for movement or loosened hardware

Do not transport the boat or kayak until the FishEye is secured according to its transportation instructions.

Before Moving the Boat

  • FishEye is fully raised

  • Transducer is clear of the water

  • Movement has stopped

  • Cables are not pinched or stretched

  • Mount and hardware remain secure

  • Storage restraint is engaged when required

  • System will not contact the trailer or surrounding equipment

  • Power is disconnected when required for transportation

Safety Notice

Keep hands, clothing, fishing line and loose equipment away from moving FishEye while it is moving. Release the control immediately if the system contacts an obstruction, binds or produces an unusual sound. Disconnect power before inspecting or clearing the assembly.

KAYAK INSTALLATION

For FishEye systems designed to provide controlled forward-facing sonar from a kayak or other compatible small watercraft.

Confirm Compatibility and Required Parts

Before beginning, confirm that the FishEye configuration is intended for your kayak and mounting setup.

Verify that you have:

  • The correct FishEye kayak configuration

  • A compatible mounting base or accessory-track connection

  • The required mounting bracket and hardware

  • A compatible sonar transducer and attachment bracket

  • The approved power source and power connection

  • Enough clearance for paddling, pedaling, steering and landing

  • ​The appropriate FishEye controls

Do not begin installation if the mounting location, power requirements or required hardware are uncertain.

Choose and Test the Mounting Position

Dry-fit the complete FishEye system before drilling or permanently fastening anything.

Check the proposed position:

  • Is within comfortable reach from the seated position

  • Does not interfere with paddling or pedaling

  • Remains clear of the rudder and steering controls

  • Allows for the FishEye to move through its full operating range

  • Keeps the transducer clear of the hull

  • Does not obstruct entry or exit from the kayak

  • Leaves a protected route for the power and transducer cables

  • Allows the system to be raised before entering shallow water or landing

Sit in the kayak on dry land and test the controls, pedals, steering and paddle clearance before securing the mount.

Secure the Kayak Mount

Position the FishEye mount according to the supplied mounting diagram.

Before tightening:

  1. Confirm the mount is correctly oriented

  2. Verify that the mounting surface or accessory track is secure

  3. Check underneath the mounting area for wiring or obstructions

  4. Install the supplied fasteners or track hardware evenly

  5. Use backing hardware or marine sealant when specified

  6. ​Confirm the mount cannot shift, loosen or rotate unexpectedly

Do not substitute mounting hardware or drill into the kayak unless FishEye or the kayak manufacturer confirms the installation method is appropriate.

Install and Align the Transducer

Attach the FishEye assembly and compatible transducer using the required bracket and hardware.

After installation:

  • Confirm all retaining hardware is engaged

  • Verify that the transducer is firmly secured

  • Position the transducer in the direction indicated by its manufacturer

  • Confirm it can move without contacting the kayak

  • Check that it remains clear of the paddle, pedal drive and rudder

  • Verify that it can be raised completely out of the water

  • Confirm the assembly does not prevent safe entry or exit

The sonar image may appear reversed or misaligned if the transducer is installed in the wrong orientation.

Route and Secure the Cables

Route the power and transducer cables only after testing the complete movement range.

Provide enough cable slack for:

  • FishEye rotation or aiming

  • Raising and lowering the system

  • Steering and pedaling operation

  • Removing or repositioning the assembly

  • Accessing the battery or power connection

Keep cables away from:

  • Pedals and the pedal-drive mechanism

  • Rudder and steering cables

  • Hinges and pinch points

  • Sharp edges

  • Loose gear and storage hatches

  • Areas used for carrying or securing the kayak

Secure excess cable without creating tight bends or tension on the connectors. Test the complete movement of the FishEye, steering system and pedal drive while watching every cable.

Test Operation and Kayak Clearance

Test the installation with the kayak safely supported on dry land.

With the boat safely parked or secured:

  1. Confirm all mounting hardware is tight

  2. Connect the approved FishEye power source

  3. Lower the FishEye into its operating position

  4. Test the complete movement and aiming range

  5. Operate the paddle, pedals and steering controls

  6. Confirm the assembly remains clear throughout every movement

  7. Watch the cables for pulling, twisting or pinching

  8. Verify that the FishEye controls aim in the expected direction

  9. Raise the FishEye completely and confirm it remains secure

Stop immediately if the assembly contacts the kayak, restricts steering or pedaling, interferes with paddling, or places tension on a cable.

Before You Launch

  • Mount and hardware are secure

  • FishEye lowers and raises without obstruction

  • Transducer orientation is correct

  • Transducer remains clear of the hull

  • Paddle, pedals and steering operate normally

  • Cables have sufficient movement slack

  • Battery and power connections are secured

  • Controls aim in the expected direction

  • FishEye can be raised before landing or entering shallow water

  • No cable enters a hinge, pedal mechanism or pinch point

Safety Notice

Disconnect power before installing or adjusting the FishEye, transducer or associated wiring. Secure the battery and all loose equipment before launching. Raise the FishEye before entering shallow water, beaching the kayak, loading it onto a vehicle or transporting it.

AIMING & SONAR CONTROL

Use the FishEye controls and directional arrow indicator to aim your forward-facing sonar and see exactly where it is looking.

Use the Directional Arrow as Your Reference

The directional arrow indicator on top of the FishEye shows the direction the sonar is aimed.

Before aiming:

  • Confirm the FishEye is fully lowered into its operating position

  • Locate the directional arrow on top of the unit

  • Verify that the arrow points toward the area being scanned

  • Confirm the transducer is installed in the correct orientation

  • Compare the arrow's direction with the sonar display

  • Make sure the FishEye can rotate without contacting another component

If the sonar image does not match the direction of the arrow, stop and check the transducer orientation.

Test the Aiming Controls

Operate each aiming control briefly to learn how the FishEye responds.

During the test:

  1. Activate one aiming direction

  2. Watch the directional arrow move

  3. Release the control and confirm movement stops

  4. Activate the opposite aiming direction

  5. Confirm the arrow moves in the expected direction

  6. Watch the cables throughout the movement

  7. Verify that the movement is smooth and unobstructed

Do not rely on the sonar image until you understand how each control changes the direction of the arrow.

Aim the Sonar Toward the Search Area

Use the directional arrow to point the sonar toward the water you want to scan.

For more precise aiming:

  • Point the arrow toward the general search area

  • Use short control inputs for small adjustments

  • Allow the sonar image to update after each movement

  • Use the boat, shoreline or visible structure as a reference

  • Avoid rapid back-and-forth movement

  • Keep the FishEye within its approved rotation range

The sonar is looking in the same direction as the arrow indicator.

Match the Arrow to the Sonar Display

Use a visible object or known underwater feature to confirm that the sonar image matches the arrow's direction.

To verify alignment:

  1. Point the directional arrow toward a known target or structure

  2. Locate that object on the sonar display

  3. Aim the arrow slightly to one side

  4. Confirm that the target moves across the display as expected

  5. Return the arrow to the original direction

  6. Repeat the test if the physical direction and sonar image do not match

If the arrow points toward a target but the sonar displays a different direction, check the transducer mounting orientation and sonar settings.

Monitor Movement and Cable Slack

Watch the directional arrow, FishEye assembly and cables when aiming through a wide range.

Stop movement if:

  • A cable begins wrapping around the shaft

  • A connector is pulled or placed under tension

  • The FishEye contacts the hull or trolling motor

  • The transducer approaches the propeller

  • The assembly reaches its approved rotation limit

  • Movement becomes slow, uneven or noisy

  • The control is released but movement continues

Do not force the FishEye past its normal stopping point or repeatedly operate it against an obstruction.

Return the Arrow to the Storage Direction

Before raising or storing the FishEye, point the directional arrow toward the required storage position.

After repositioning:

  1. Confirm the arrow points in the correct storage direction

  2. Check that the cables are not twisted

  3. Verify that the FishEye can raise without contacting the boat

  4. Confirm the transducer remains clear of the hull and motor

  5. Raise the FishEye into its stored position

  6. Secure the system when operation is complete

Returning the arrow to a consistent storage direction helps prevent cable twisting and interference while raising the FishEye.

Before You Continue Fishing

  • FishEye is fully lowered

  • Transducer orientation is correct

  • Directional arrow accurately shows where the sonar is aimed

  • Both aiming directions respond correctly

  • Movement stops when the control is released

  • Arrow direction matches the sonar display

  • FishEye moves smoothly without obstruction

  • Cables have sufficient slack and are not twisting

  • Transducer remains clear of the hull and propeller

  • Approved rotation limits are understood

  • FishEye can return to its storage position

Safety Notice

Use the FishEye and directional arrow for sonar aiming only - not for navigation or collision avoidance. Keep hands, fishing line and loose equipment away from moving components. Release the control immediately if the system binds, contacts another component or places tension on a cable.

NO POWER

Use these checks when the FishEye does not turn or respond to its controls.

Confirm the Correct Power Source

Verify that the connected power source is approved for your FishEye configuration.

Check:

  • The battery type matches the FishEye requirements

  • A 12V connection uses the correct voltage and polarity

  • A tool battery is compatible with the installed adapter

  • The battery is fully seated or securely connected

  • The power source is not visibly damaged

  • The battery has enough charge to operate the system

Do not connect a battery, adapter or voltage that has not been approved for the FishEye.

Check the Battery Charge

A battery may have enough power for an indicator light but not enough to operate the FishEye under load.

For a tool battery:

  1. Remove the battery from the adapter

  2. Inspect the terminals for dirt, corrosion or damage

  3. Fully charge the battery with its approved charger

  4. Reinstall it until it is completely seated

  5. Test the FishEye again

  6. Try another approved, fully charged battery when available

For boat power, confirm the battery is charged and other connected equipment is not causing excessive voltage loss.

Inspect the Power Connections

Disconnect power before inspecting any wiring or connectors.

Check for:

  • A loose battery or adapter connection

  • A connector that is not fully seated

  • Reversed polarity on a wired connection

  • Corrosion, dirt or moisture inside a connector

  • Bent, recessed or damaged connector pins

  • Cut, crushed, pinched or stretched wiring

  • A connection that becomes hot during use

Clean and reconnect only according to the supplied instructions. Do not operate with damaged wiring or connectors.

Check the Fuse, Breaker or Power Switch

Inspect any external protection device or switch used by the FishEye power circuit.

Confirm that:

  • The boat's battery switch is on

  • The correct circuit or accessory switch is activated

  • The circuit breaker has not tripped

  • The installed fuse is not blown

  • The fuse holder is clean and securely closed

  • The correct replacement fuse is used when replacement is required

Do not bypass a fuse or breaker or install a higher-rated fuse to restore power.

Test the Power Source

If the FishEye does not power on, determine whether power is reaching the system.

When it is safe to do so:

  • Disconnect the FishEye

  • Test the battery or power outlet with an appropriate meter

  • Confirm the voltage is within the approved operating range

  • Check voltage at the FishEye connection

  • Inspect for a voltage drop caused by loose or undersized wiring

  • Reconnect the system and test one control at a time

If you are not comfortable testing marine electrical wiring, stop and contact FishEye or a qualified installer.

Isolate the Problem

Use approved components to identify whether the problem is with the battery, wiring, controller or FishEye unit.

Try the following:

  • Test with another approved, fully charged battery

  • Test the battery in its approved charger or another compatible device

  • Reconnect every accessible external connector

  • Confirm the controller has power

  • Remove unapproved adapters or extension wiring

  • Test the FishEye directly from an approved power connection when permitted

  • Record any indicator lights, sounds or brief movement

Stop troubleshooting if wiring is damaged, a fuse blows repeatedly or a component becomes hot.

Before Contacting Support

  • Correct power source is being used

  • Battery is fully charged

  • Battery or adapter is completely seated

  • Polarity is correct

  • Connectors are clean and secure

  • Wiring is not cut, pinched or corroded

  • Power switch is on

  • Fuse or breaker has been checked

  • Approved voltage reaches the FishEye connection

  • Controller power has been checked

  • No component becomes hot or produces an odor

When contacting FishEye, provide the model or configuration, power-source type, battery voltage if tested, controller behavior and any indicator lights or sounds.

Safety Notice

Disconnect power before inspecting wiring, connectors, fuses or moving components. Never bypass circuit protection, use damaged wiring or connect an unapproved voltage. Stop immediately if a component becomes hot, produces smoke or gives off a burning odor.

REMOTE & CONTROL FUNCTIONS

Use the FishEye controls to raise, lower and aim your sonar independently from the boat or trolling motor.

Identify the Controls

Before operating the FishEye, locate each control and confirm its function.

The controls may include:

  • Raise - moves the sonar assembly upward

  • Lower - moves the sonar assembly downward

  • Left - aims the sonar to the left

  • Right - aims the sonar to the right

  • Stop - stops the current movement, if equipped

  • Power - activates or deactivates the system, if equipped

Control labels and button placement may vary by configuration. Confirm the function of each button before using the system on the water.

Check the Area Before Moving

Look around the FishEye assembly before pressing any control.

Confirm that:

  • The transducer is clear of the trailer and ground

  • No person is near the moving assembly

  • Cables are free from obstructions

  • The shaft is not caught against the boat

  • The transducer has room to raise, lower and rotate

  • The boat is in a safe position for testing

Stop if any part of the system is blocked.

Raise and lower the Sonar

Use the appropriate control to move the transducer vertically.

When operating the lift:

  1. Press the Lower control to move the transducer toward the water

  2. Watch the assembly as it moves

  3. Stop when the transducer reaches the correct operating depth

  4. Press the Raise control before entering shallow water, approaching an obstruction or loading the boat

  5. Confirm the assembly is fully raised before trailering

Do not continue holding the control after the assembly reaches its normal travel limit.

Aim the Sonar

Use the directional controls to aim the transducer toward the area you want to scan.

While aiming:

  • Press Left or Right to rotate the sonar

  • Use short adjustments for more precise aiming

  • Watch the directional arrow on top of the FishEye

  • The arrow indicates the direction the sonar is facing

  • Compare the arrow direction with the image displayed on your sonar unit

  • Stop rotation if cables begin pulling or twisting

The directional arrow is the primary visual reference for sonar direction.

Use the Controls While Fishing

Make controlled adjustments instead of continuously operating multiple functions.

For normal use:

  • Lower the transducer only after the boat is in the water

  • Aim the sonar toward the target area

  • Use small left or right movements while tracking fish or structure

  • Raise the assembly before entering shallow water

  • Raise it before approaching docks, vegetation or submerged objects

  • Return the assembly to its safe travel position before loading the boat

Do not operate the system when the transducer's movement cannot be observed safely.

Stop and Check Unexpected Operation

Release the control immediately if the FishEye:

  • Moves in the wrong direction

  • Does not stop when expected

  • Makes unusual sounds

  • Stops before reaching its normal position

  • Pulls or twists a cable

  • Contacts the boat or trolling motor

  • Responds inconsistently to the controls

Disconnect power before inspecting the system. Do not force the shaft, rotator or lift assembly by hand.

Before You Fish

  • Every control performs the expected function

  • Raise and lower movement is smooth

  • Left and right aiming works correctly

  • The directional arrow matches the sonar direction

  • The assembly stops when the control is released

  • Cables remain free during complete movement

  • The transducer is clear of the boat and propeller

  • The system can be fully raised before trailering

Safety Notice

Keep hands, clothing, fishing line and tools away from the FishEye while it is moving. Disconnect power before inspecting, adjusting or servicing the system.

RAISE & LOWER

Use these checks when the FishEye will not move, stops early or moves differently than expected.

Stop and Inspect the System

Release the control immediately if the FishEye stops moving, binds or makes an unusual sound.

Before testing again:

  • Keep hands away from moving components

  • Disconnect power

  • Confirm the FishEye has not contacted the boat dock or trailer

  • Check for visible damage or misalignment

  • Look for fishing line, weeds, mud or debris

  • Verify that no cable is wrapped around the assembly

  • Confirm the transducer has not struck an obstruction

Do not continue activating the controls when the system cannot move freely.

Remove Storage Restraints and Obstructions

Confirm that nothing is preventing the FishEye from leaving its stored or operating positions.

Check for:

  • An attached transportation strap or storage lock

  • A shaft caught against the mount

  • A cable trapped in movement path

  • Fishing line or weeds wrapped around the assembly

  • Ice, sand, mud or debris moving around parts

  • Contact with the hull, trolling motor or mounting bracket

  • Insufficient water depth beneath the transducer

Disconnect power before removing an obstruction. Never reach near a moving system.

Check the Power Supply

Low or interrupted power may allow the controls to respond without moving the FishEye correctly.

Confirm that:

  1. The approved power source is connected

  2. The battery is fully charged

  3. The battery or adapter is completely seated

  4. The connectors are clean and secure

  5. The fuse or breaker has not opened

  6. The wiring is not loose, pinched or damaged

  7. No connector becomes hot during operation

If the FishEye has no power at all, follow the No Power troubleshooting section first.

Test the Raising and Lowering Controls

Test one control at a time with the FishEye's movement path completely clear.

During the test:

  • Press the lowering control briefly

  • Release it and confirm movement stops

  • Press the raising control briefly

  • Confirm the correct function responds

  • Check whether one direction works but the other does not

  • Listen for motor operation or unusual sounds

  • Watch for delayed, uneven or unexpected movement

If a control sticks or performs the wrong function, stop using the FishEye and disconnect power.

Check Alignment and Cable Movement

Inspect the FishEye for anything that could create resistance during movement.

Confirm that:

  • The mount has not shifted or loosened

  • The shaft remains correctly aligned

  • The transducer bracket is not contacting the boat

  • Cables have enough slack for complete movement

  • No cable enters a hinge or pinch point

  • Connectors are not carrying the weight of cable

  • Moving components are not bent, loose or damaged

Do not straighten, disassemble or lubricate internal components unless instructed by FishEye.

Test and Identify Where Movement Stops

After removing visible obstructions, reconnect power and test the FishEye carefully.

  1. Start from a clear, supported position

  2. Activate the control briefly

  3. Watch where the movement slows or stops

  4. Release the control before the system strains

  5. Test the opposite direction

  6. Record whether the problem occurs at the same position

  7. Note any sounds, controller behavior or visible movement

  8. Disconnect power if the problem continues

Stop troubleshooting if wiring is damaged, a fuse blows repeatedly or a component becomes hot.

Before Contacting Support

  • Storage restraint has been removed

  • Movement path is clear

  • Water depth is sufficient

  • Battery is fully charged

  • Power connections are secure

  • Fuse or breaker has been checked

  • Raising and lowering controls were tested separately

  • Mount and shaft alignment were inspected

  • Cables are not pinched, wrapped or under tension

  • No component is bent or visibly damaged

  • The position where movement stops has been recorded

  • Unusual sounds or controller behavior have been noted

When contacting FishEye, provide the model or configuration, power-source type, direction that will not move, position where movement stops and any unusual sounds or visible damage.

Safety Notice

Disconnect power before inspecting, adjusting or clearing the FishEye. Never place your hands in the movement path, force the shaft manually or repeatedly activate the system against an obstruction.

AIMING & CONTROLS

Use these checks when the FishEye will not aim, responds inconsistently or moves in the wrong direction

Identify the Control Problem

Test one aiming control at a time to determine what is not working.

Check whether:

  • Neither aiming direction responds

  • Only one direction responds

  • Movement is slow or intermittent

  • The FishEye moves opposite the expected direction

  • Movement continues after releasing the control

  • The directional arrow stops before reaching the desired position

  • The controller works only at close range

Stop immediately if the FishEye moves unexpectedly or continues moving after the control is released.

Check Power and Controller Readiness

Confirm that both the FishEye and its controller have sufficient power.

Verify that:

  • The approved FishEye power source is connected

  • The main battery is sufficiently charged

  • The controller is powered on, when applicable

  • The controller battery is charged or installed correctly

  • The controller is within its approved operating range

  • The FishEye responds to another function, such as raising or lowering

If no FishEye function responds, follow the No Power troubleshooting section first.

Check for Rotation Obstructions

Disconnect power and inspect the complete aiming path.

Look for:

  • A cable wrapped around the shaft

  • Fishing line, weeds or debris

  • Contact with the hull or trolling motor

  • A transducer bracket striking another component

  • A shifted or loosened mount

  • A bent or misaligned component

  • Insufficient clearance around the directional arrow assembly

  • A storage restraint that remains attached

Do not force the FishEye past an obstruction or turn the assembly manually unless FishEye instructions specifically permit it.

Inspect Cable Slack and Connections

A tight, twisted or damaged cable can restrict aiming or interrupt control response.

Confirm that:

  • The cables have enough slack for the approved aiming range

  • No cable is pulling against a connector

  • The cables are not wrapped around the shaft

  • No cable enters a hinge or pinch point

  • Connectors are fully seated

  • Connector pins are clean and undamaged

  • Wiring is not cut, crushed, stretched or corroded

Secure excess cable without creating tension or tight bends.

Check Arrow and Sonar Alignment

The directional arrow on top of the FishEye should indicate where the sonar is aimed.

To check alignment:

  1. Lower the FishEye into its normal operating position

  2. Point the arrow toward a visible reference

  3. Confirm the transducer points in the corresponding direction

  4. Locate the reference area on the sonar display

  5. Move the arrow slightly in each direction

  6. Confirm the sonar image changes as expected

  7. Stop if the arrow, transducer and sonar image do not agree

Misalignment may be caused by incorrect transducer orientation, shifted hardware or an incorrect control configuration.

Reconnect and Test One Function at a Time

After confirming the movement path is clear, reconnect the approved power source and test carefully.

  1. Place the boat or kayak in a safe, secured position

  2. Activate one aiming direction briefly

  3. Release the control and confirm movement stops

  4. Test the opposite direction

  5. Watch the directional arrow during each movement

  6. Monitor every cable for twisting or tension

  7. Note any delayed response, unusual sound or stopping position

  8. Disconnect power if the problem continues

Do not repeatedly operate the FishEye against its movement limit or an obstruction.

Before Contacting Support

  • FishEye power source is connected and charged

  • Controller power or battery has been checked

  • Controller is within operating range

  • Buttons are not stuck or damaged

  • Rotation path is clear

  • Mount and transducer bracket are secure

  • Cables are clean and fully seated

  • Both aiming directions were tested separately

  • Directional arrow movement was observed

  • Arrow direction matches the transducer and sonar image

  • Unusual sounds or stopping positions were recorded

When contacting FishEye, provide the model or configuration, controller type, affected direction, arrow behavior, power-source type and whether raising and lowering still works.

Safety Notice

Disconnect power before inspecting the FishEye, removing any obstruction or adjusting cables. Never place your hands in the movement path, force the assembly manually or continue operating a control that sticks or causes unexpected movement.

SONAR IMAGE

Use these checks when the sonar image is missing, weak, reversed or does not match the directional arrow.

Identify the Image Problem

Determine what appears incorrect before changing any settings or hardware.

Check whether:

  • No sonar image appears

  • The image is weak or intermittent

  • The display shows excessive noise or interference

  • The image appears reversed

  • The image freezes while aiming

  • Targets appear in the wrong direction

  • The sonar image does not match the directional arrow

Record the symptoms and any message shown on the sonar displays.

Check the Transducer Position

Confirm that the transducer is correctly positioned for normal sonar operation.

Verify that:

  • The FishEye is fully lowered

  • The transducer is below the waterline

  • The transducer has a clear view into the water

  • The transducer is not blocked by the hull

  • No weeds, mud, fishing line or debris cover its surface

  • The transducer remains clear of the propeller

  • The FishEye is stable and not vibrating excessively

Raise the FishEye and disconnect power before removing debris or inspecting the transducer closely.

Confirm Direction and Orientation

The directional arrow on top of the FishEye indicates where the sonar should be aimed.

To check alignment:

  1. Point the arrow toward a visible reference area

  2. Confirm the transducer is physically aimed in the corresponding direction

  3. Locate the area or structure on the sonar display

  4. Move the arrow slightly to one side

  5. Confirm the sonar image changes as expected

  6. Inspect the transducer mounting orientation if the directions do not match

  7. Confirm the transducer is installed according to its manufacturer's instructions

A reversed or misaligned image is often caused by incorrect transducer orientation or sonar settings.

Inspect the Transducer Cable

Disconnect power before inspecting the transducer cable and connectors.

Check for:

  • A connector that is not fully seated

  • Bent or damaged connector pins

  • Moisture, dirt or corrosion

  • Cuts, crushing or abrasion

  • A cable pinched by the FishEye or mount

  • Excessive tension at either connector

  • Tight bends or cable wrapping

  • Routing alongside equipment that may cause interference

Do not splice, shorten or repair a transducer cable unless the sonar manufacturer specifically permits it.

Check the Sonar Display Settings

Confirm that the sonar unit is configured for the installed transducer and desired view.

Review:

  • Selected sonar source

  • Transducer selection

  • Forward-facing sonar mode

  • Range and depth settings

  • Gain and sensitivity

  • Noise-rejection settings

  • Image orientation

  • Software or firmware status

Change one setting at a time so you can identify what corrects the image. Use the sonar manufacturer's instructions for model-specific settings.

Isolate the FishEye or Sonar Problem

Determine whether the issue follows the FishEye's movement or remains within the sonar system.

  1. Point the directional arrow toward a known reference

  2. Observe the sonar image

  3. Aim the FishEye in another direction

  4. Confirm the arrow and transducer move together

  5. Check whether the sonar image updates

  6. Reconnect accessible external sonar connections

  7. Restart the FishEye and sonar according to their instructions

  8. Record whether the issue changes with direction or movement

If the FishEye aims correctly but the image remains incorrect, the sonar unit, transducer, cable or display settings may require manufacturer support.

Before Contacting Support

  • FishEye is fully lowered

  • Transducer is below waterline

  • Transducer surface is clean

  • Transducer has a clear view into the water

  • Directional arrow movement was checked

  • Arrow and transducer point in corresponding directions

  • Transducer orientation was inspected

  • Cable and connectors are secure and undamaged

  • Sonar source and transducer selection were checked

  • Image settings were reviewed

  • FishEye and sonar were restarted

  • Display messages and symptoms recorded

When contacting FishEye, provide the model or configuration, sonar brand and model, transducer model, image symptoms, arrow behavior and clear photos of the transducer installation and display.

Safety Notice

Raise the FishEye and disconnect power before inspecting the transducer, cable or mounting hardware. Never reach near a propeller or place your hands in the FishEye's movement path.

BOAT COMPATIBILITY

Use these checks to determine whether a FishEye configuration will work with your boat or kayak.

Choose Your Mounting Style

Start by selecting how and where you want to use the FishEye.

Available configurations may include:

  • Permanent Transom: Permanently attached to the rear of the boat

  • Removable Clamp: Clamped to the transom without permanent mounting

  • Bow-Mount Rotator: Installed near the trolling motor for independent sonar aiming

  • Kayak/Small Watercraft: Attached to a compatible accessory track or approved mounting point

Choose the configuration based on the location where the FishEye will actually be installed.

Find the Mounting Location

Locate the area where the selected FishEye configuration would attach.

  • Permanent Transom: On the rear transom, typically to the left of the outboard motor

  • Removable Clamp: On an accessible transom edge where the clamp can sit completely

  • Bow-Mount Rotator: On the bow near the trolling motor, with room for both systems to operate

  • Kayak/Small Watercraft: On a compatible accessory track or mounting point within reach of the seated operator

Do not drill or tighten the mount yet. Hold or dry-fit the FishEye in a proposed location first.

Measure the Required Clearance

Measure from the proposed FishEye mounting point to the bottom of the hull.

Also check that there is enough space for the FishEye to:

  • Lower the transducer below the hull

  • Raise the transducer completely out of the water

  • Aim through its approved range

  • Remain clear of the outboard motor and propeller

  • Avoid the trolling motor and steering components

  • Stay clear of swim platforms, trim tabs and ladders

  • Avoid contact with the trailer or dock

Record the mounting-point-to-hull-bottom measurement before selecting FishEye configuration.

Check the Complete Movement Range

Dry-fit the FishEye and test the space it will require during normal operation.

Confirm that it can:

  1. Lower without contacting the hull

  2. Reach the required operating depth

  3. Aim without contacting another component

  4. Remain clear while the motor is steered or trimmed

  5. Raise completely into its stored position

  6. Avoid the trolling motor during deployment and storage

  7. Remain clear of the trailer and dock

  8. Operate without pulling or twisting its cables

A location may appear compatible while stationary but interfere when the motor or FishEye moves.

Check Mounting and Cable Requirements

After confirming clearance, inspect the exact area where the mount will attach.

Verify that:

  • The mounting area is solid and undamaged

  • The mount or clamp fits completely against the surface

  • The surface is flat enough for the selected hardware

  • There is room for bolts or backing hardware when required

  • No wiring, plumbing or equipment is hidden behind the area

  • Power and transducer cables can reach the location

  • Cables can be secured away from hinges and moving components

  • The mount will not interfere with normal boat use

Do not drill into the boat until the mounting area and everything behind it have been inspected.

Confirm Compatibility Before Ordering

If any measurement, mounting location or clearance is uncertain, contact FishEye before ordering or drilling.

Provide:

  • Boat or kayak manufacturer

  • Model and year

  • Hull material

  • Selected mounting style

  • Mounting-point-to-hull-bottom measurement

  • Outboard or trolling-motor information

  • Intended power source

  • Photos of the proposed mounting location

  • Photos showing nearby motors and equipment

  • Whether the installation should be permanent or removable

FishEye can use this information to identify the appropriate configuration and possible installation concerns.

Compatibility Checklist

  • Mounting style has been selected

  • Correct mounting area has been located

  • FishEye has been dry-fitted

  • Mounting-point-to-hull-bottom measurement is known

  • Transducer can extend below the hull

  • FishEye can raise completely

  • Aiming movement is unobstructed

  • Motor and propeller clearance is sufficient

  • Steering and trim movement were checked

  • Trolling-motor deployment and storage were checked

  • Mounting area is solid and accessible

  • Cable-routing space is available

  • Trailer and dock clearance were considered

  • Compatibility is confirmed before drilling

Safety Notice

Do not drill into the boat or permanently install hardware until the area has been inspected for hidden wiring, plumbing and structural concerns. Keep the FishEye and transducer clear of the propeller, steering system and other moving equipment.

SONAR COMPATIBILITY

FishEye works with select forward-facing sonar transducers.

Garmin

  • LiveScope LVS32

  • LiveScope Plus LVS34

  • LiveScope XR LVS62

Lowrance

  • ActiveTarget

  • ActiveTarget 2

  • ActiveTarget 2 XL

Humminbird

  • MEGA Live Imaging

  • MEGA Live 2

Don't See Your Transducer?

Contact FishEye with the brand, exact model number and a photo of the transducer.

POWER COMPATIBILITY

FishEye works with select 12V boat-power and tool-battery configurations.

12V Boat Power

Compatible with:

  • 12V marine battery systems

  • Approved FishEye power wiring

  • Required inline fuse or circuit protection

  • Correct positive and negative connections

The FishEye must be connected using the approved voltage, wiring and fuse rating.

Tool Battery Power

Requires an 18V/20V lithium-ion tool battery and the matching FishEye adapter.

  • Battery Platform: 18V or 20V MAX

  • Battery Type: Lithium-ion

  • Recommended Capacity: 5.0 Ah or greater

  • Battery and charger sold separately

Battery capacity affects operating time, not adapter compatibility. Higher amp-hour batteries generally provide longer use.

BOW-MOUNT COMPATIBILITY

Check whether your bow setup has the required mounting space and clearance.

Minimum Mounting Requirements

Your bow setup should provide:

  • 6 x 6 inches of solid mounting surface

  • At least 8 inches between the FishEye mounting point and trolling motor

  • At least 3 inches of clearance around the rotation assembly

  • A clear path for the FishEye to rotate without contacting the trolling motor

  • Enough room for the trolling motor to deploy and stow completely

  • A protected route for the power and transducer cables

Check the Complete Movement Range

Before drilling, position the FishEye in the proposed location and confirm.

  • The trolling motor deploys completely

  • The trolling motor stores completely

  • The trolling motor can steer through its full range

  • The FishEye can rotate without contact

  • The transducer remains clear of the propeller

  • Cables do not stretch, twist or enter a pinch point

Your Setup May Not Be Compatible If

  • Less than 6 x 6 inches of mounting surface is available

  • The FishEye would be within 8 inches of the trolling motor

  • The trolling motor crosses the FishEye's rotation path

  • The transducer could enter the propeller path

  • Cables must pass through the deployment mechanism

  • The mounting surface flexes or cannot accept the required hardware

Not Sure About Your Setup?

Send FishEye:

  • Trolling-motor brand and model

  • Photo with the motor deployed

  • Photo with the motor stored

  • Photo of the proposed mounting area

  • Available mounting-area dimensions

  • ​Distance from the mounting point to the trolling motor

Safety Notice

Do not drill into the boat or permanently install hardware until the area has been inspected for hidden wiring, plumbing and structural concerns. Keep the FishEye and transducer clear of the propeller, steering system and other moving equipment.

BOW-MOUNT ROTATOR INSTALLATION

For FishEye systems that aim forward-facing sonar independently from the trolling motor's steering direction.

Confirm Compatibility and Required Parts

Before beginning, confirm that the FishEye configuration is intended for your trolling motor and bow setup.

Verify that you have:

  • The correct FishEye rotator configuration

  • The required mounting bracket and hardware

  • A compatible sonar transducer and attachment bracket

  • The correct power connection

  • Enough clearance for deployment and storage

  • ​The appropriate FishEye controls

Do not begin installation if the mounting configuration or required hardware is uncertain.

Choose and Test the Mounting Position

Dry-fit the FishEye system before drilling or permanently fastening anything.

Check the proposed position:

  • Does not interfere with trolling-motor deployment or storage

  • Remains clear of the trolling-motor shaft

  • Allows the transducer clear of the propeller

  • Does not block access to existing bow controls

  • Leaves a safe path for power and transducer cables

Deploy, stow and steer the trolling motor through its full range while checking clearance.

Secure the Rotator Mount

Position the FishEye mount according to the supplied mounting diagram.

Before tightening:

  • Confirm the mount is correctly oriented

  • Check underneath the mounting surface for wiring or obstructions

  • Verify that the mounting surface is solid

  • Install the supplied fasteners evenly

  • Use backing hardware or marine sealant when specified

  • Confirm the mount cannot shift, flex or rotate unexpectedly

Do not substitute mounting hardware unless FishEye confirms that it is appropriate.

Install and Align the Transducer

Attach the FishEye rotating assembly and compatible transducer using the required bracket and hardware.

After installation:

  • Confirm all retaining hardware is engaged

  • Verify that the transducer is firmly secured

  • Position the transducer in the direction indicated by its manufacturer

  • Check that it can rotate without contacting the trolling motor

  • Confirm the transducer remains clear of the propeller

  • Verify that the assembly does not interfere with stowing or deploying the motor.

The sonar image may appear reversed or misaligned if the transducer is installed in the wrong orientation.

Route Power and Transducer Cables

Route the cables only after confirming the system's complete range of movement.

The cables should:​

  • Stay clear of the propeller and motor.

  • Avoid sharp edges and hot surfaces.

  • Have enough slack for normal FishEye movement.

  • Not hang loosely where they can snag.

  • Be supported with marine-grade cable ties or clamps.

  • Avoid tight bends, pinch points and excessive tension.

Leave the power disconnected while routing or adjusting wiring. Connect power only according to the FishEye power instructions.

Test Before Use

Test the complete installation before launching the boat.

With the boat safely parked or secured:

  • Confirm all mounting hardware is tight

  • Deploy the trolling motor

  • Connect the approved FishEye power source

  • Test the complete rotation range

  • Steer the trolling motor independently

  • Confirm the FishEye remains clear throughout both movements

  • Watch the cables for pulling, twisting or pinching

  • Verify that the FishEye controls aim in the expected direction

  • Stow the trolling motor and recheck all clearances

Stop immediately if the assembly contacts the motor, restricts steering or places tension on a cable.

Download FishEye manuals and product guides

MANUALS & DOWNLOADS

Download quick start guides, manuals, specifications and

other product resources.

CONTACT FISHEYE

We're here to help.

Email FishEye support

EMAIL SUPPORT

info@fisheye.vision

We typically respond within 1 business day.

Call FishEye support

CALL US

(971) 490-2129

Mon-Fri: 8am - 5pm Pacific Time

FishEye mailing address

MAILING ADDRESS

P.O. Box 1493

Oregon City, OR 97045

SEND US A MESSAGE

Have a question about a product, an order,  installation, or support? Send us the details below and the FishEye team will help you find the right answer.

FishEye Model
bottom of page